Listar ICMF - Artículos por título
Mostrando ítems 1-15 de 15
-
A Novel Methodology to Obtain the Mechanical Properties of Membranes by Means of Dynamic Tests
(IOAP-MPDI, 2022-03-02)A new, non-destructive methodology is proposed in this work in order to determine the mechanical properties of membrane using vibro-acoustic tests. This procedure is based on the dynamic analysis of the behavior of the ... -
Analysis of the Effect of the Surface Inclination Angle on the Roughness of Polymeric Parts Obtained with Fused Filament Fabrication Technology
(2023-01-23)The aim of this work was to conduct a dimensional study, in terms of microgeometry, using parts from an additive manufacturing process with fused filament fabrication (FFF) technology. As in most cases of additive manufacturing ... -
Analysis of the Effect of the Surface Inclination Angle on the Roughness of Polymeric Parts Obtained with Fused Filament Fabrication Technology
(IOAP-MDPI, 2023-01-23)The aim of this work was to conduct a dimensional study, in terms of microgeometry, using parts from an additive manufacturing process with fused filament fabrication (FFF) technology. As in most cases of additive manufacturing ... -
Characterisation of the crack tip plastic zone in fatigue via synchrotron X-ray diffraction
(Universidad de Málaga, 2022-04-23)This paper describes a new methodology for characterising the plastic zoneahead of a fatigue crack. This methodology is applied to a set of experimentaldata obtained by synchrotron X-ray diffraction on a bainitic steel ... -
Critical plane based method for multiaxial fatigue analysis of 316 stainless steel
(Elsevier, 2022-04)In this work, the fatigue behaviour of 316 stainless steel is studied with different critical plane models. Seven cylindrical samples were used for the study, being subjected to different complex loading paths, generating ... -
Energy-based critical plane fatigue methods applied to additively manufactured 18Ni300 steel
(Elsevier, 2023)In this work, the uniaxial and biaxial fatigue behaviour of maraging steel (18Ni300) obtained by additive manufacturing was studied. The material was evaluated using several biaxial load paths and different load levels. ... -
Experimental viscoelastic properties evaluation, under impact loads and large strain conditions, of coated & uncoated rubber from end-of-life tires
(Experimental viscoelastic properties evaluation, under impact loads and large strain conditions, of coated & uncoated rubber from end-of-life tires, 2022-03)End-of-life tires (ELTs) pose a serious environmental problem today due to their great ability to maintain their properties and not degrade under extreme conditions or over time. One of the ways to reuse this material ... -
Fatigue crack characterisation in 2024-T351 aluminium alloy through SEM observation combined with the CJP model
(Elsevier, 2023-01)This work characterises crack growth in AA2024-T315 by combining different methods to further increase the reliability of the results. The Christopher-James-Patterson (CJP) model was fitted to experimental data obtained ... -
Fatigue crack propagation analysis in 2024-T351 aluminium alloy using nonlinear parameters
(ELSEVIER, 2021-12)In this work, fatigue crack growth (FCG) in the 2024-T351 aluminium alloy is studied using the plastic CTOD range, Δδp. Experimental tests were performed on 12 mm thick CT specimens in order to obtain FCG rate and in ... -
Geometrical analysis in material extrusion process with polylactic acid (PLA)1carbon fiber.
(Emerald, 2022-12-22)Purpose: The purpose of this study is to cover the influence of selected printing parameters at a macro and micro-geometrical level, focusing on the dimensions, geometry and surface of printed parts with short carbon ... -
Influence of Infill Pattern on Mechanical Behavior of Polymeric and Composites Specimens Manufactured Using Fused Filament Fabrication Technology
(Polymers, 2021)This paper presents the results of a comparative evaluation of the tensile strength behaviors of parts obtained by additive manufacturing using fused filament fabrication (FFF) technology. The study investigated the ... -
Numerical model characterization of the sound transmission mechanism in the tympanic membrane from a high-speed digital holographic experiment in transient regime
(Elsevier, 2023)A methodology for the development of a finite element numerical model of the tympanic membrane (TM) based on experiments carried out in the time domain on a cadaveric human temporal bone is presented. Using a high-speed ... -
Special Issue of the Manufacturing Engineering Society 2021 (SIMES-2021)
(IOAP-MPDI, 2022-07-07)After the complete success of the first, second, and third editions of the Special Issues of the Manufacturing Engineering Society (SIMES), with a total of 118 contributions (94 in Materials and 24 in Applied Sciences) ... -
Study of Abrasive Water Jet Machining as a Texturing Operation for Thin Aluminium Alloy UNS A92024
(MDPI, 2023-05-19)Surface modification of metallic alloys can create hydrophilic or hydrophobic surfaces that enhance the functional performance of the material. For example, hydrophilic surfaces have improved wettability, which improves ... -
The Upper Bound Theorem in Forging Processes: Model of Triangular Rigid Zones on Parts with Horizontal Symmetry
(Applied Sciences, 2020-12-31)This paper presents the analytical method capacity of the upper bound theorem, under modular approach, to extend its application possibilities. Traditionally, this method has been applied in forging processes, considering ...